考虑椭圆盘随机κ值的三维离散裂隙网络建模方法Three-dimensional discrete fracture network modeling incorporating the random aspect ratio(κ) of elliptical disks
周育东,段东,李杰,冯小静,杜丽敏,常永康,王泉栋,常明港
摘要(Abstract):
岩体裂隙三维几何参数的精确表征是工程岩体稳定性分析的关键难题.传统基于钻孔电视成像的离散裂隙网络(DFN)反演方法通常将椭圆盘裂隙模型长宽比κ简化为固定常数,难以反映真实裂隙形状的随机分布特征,易导致重构模型的裂隙几何参数与实际裂隙存在较大偏差.为此,提出一种考虑κ对数正态随机性的椭圆盘DFN建模方法 .首先,基于参数分布函数构建考虑κ随机性的椭圆盘裂隙模型参数集;其次,利用钻孔与裂隙的相交几何关系,推导了裂隙中心位于“有效探测面积”内即被钻孔揭露的条件,建立了钻孔裂隙观测数量N、线密度P_(10)与岩体裂隙群参数(体密度P_(30)、尺寸a及长宽比κ)之间的理论期望关系;最后,构建了矩匹配加权最小二乘反演框架,实现了上述参数的同步估计与不确定性量化,并形成了与钻孔观测数据严格对齐的三维DFN模型重建流程.结果表明:相较于传统固定κ模型,随机κ模型对钻孔裂隙计数的拟合与预测误差显著降低,留一孔交叉验证的最大相对误差由最大值16.12%降至6.25%.工程实例进一步表明,随机κDFN模型与实测钻孔数据的相对误差由固定κDFN模型的最大值15%降低至8.5%,对裂隙面密度P_(32)的估计值稳定在0.40~0.60 m~2/m~3之间,500组蒙特卡洛模拟的平均值约为0.51 m~2/m~3,模型自身误差小于10%.兼顾裂隙数量、尺寸及体量匹配,研究明确了将κ视为随机变量的必要性和有效性,可为基于有限勘探数据的岩体裂隙网络精细建模及稳定性评价提供新思路.
关键词(KeyWords): 随机形状;椭圆盘裂隙模型;矩匹配加权最小二乘法;三维DFN
基金项目(Foundation): 国家自然科学基金面上项目(52474139,52274134);; 山西省基础研究计划项目(202403011242005)
作者(Author): 周育东,段东,李杰,冯小静,杜丽敏,常永康,王泉栋,常明港
DOI: 10.13247/j.cnki.jcumt.20250563
参考文献(References):
- [1]王成,张农,李桂臣,等.上行开采顶板不同区域巷道稳定性控制原理[J].中国矿业大学学报,2012,41(4):543-550.Wang Cheng, Zhang Nong, Li Guichen, et al. Control principles for roadway roof stabilization in different zones during ascending mining[J]. Journal of China University of Mining&Technology , 2012, 41(4):543-550.
- [2]周四宝.水工岩体离散裂隙网络多面体模拟及其应用[D].天津:天津大学,2016.Zhou Sibao. Polyhedral simulation of discrete fracture network in rock mass of hydraulic engineering and its application[D]. Tianjin:Tianjin University, 2016.
- [3]侯朝炯,王襄禹,柏建彪,等.深部巷道围岩稳定性控制的基本理论与技术研究[J].中国矿业大学学报,2021, 50(1):1-12.Hou Chaojiong, Wang Xiangyu, Bai Jianbiao, et al.Basic theory and technology study of stability control for surrounding rock in deep roadways[J]. Journal of China University of Mining&Technology, 2021, 50(1):1-12.
- [4]孙意成,魏玉峰,胡舒寒,等.考虑离散裂隙网络非线性渗流的岩体渗透特性研究[J].岩石力学与工程学报,2025, 44(9):2444-2455.Sun Yicheng, Wei Yufeng, Hu Shuhan, et al. Permeability characteristics of rock masses incorporating nonlinear flow behaviors in discrete fracture networks[J].Chinese Journal of Rock Mechanics and Engineering,2025, 44(9):2444-2455.
- [5]姚荣文,张云辉,赵晓彦,等.岩体裂隙三维可视化新方法及其应用[J].地球科学,2022, 47(9):3463-3476.Yao Rongwen, Zhang Yunhui, Zhao Xiaoyan, et al.A new 3D visualization method for rock mass fractures and its application[J]. Earth Science, 2022, 47(9):3463-3476.
- [6]刘灿灿,郑西贵,王术龙,等.基于钻孔成像的结构面智能化识别系统[J].采矿与安全工程学报,2024,41(4):720-729.Liu Cancan, Zheng Xigui, Wang Shulong, et al. Research on intelligent identification system of structural plane based on borehole imaging[J]. Journal of Mining&Safety Engineering, 2024, 41(4):720-729.
- [7]Li S J, Feng X T, Wang C Y, et al. ISRM suggested method for rock fractures observations using a borehole digital optical televiewer[J]. Rock Mechanics and Rock Engineering, 2013, 46(4):635-644.
- [8]Gao B B, Wang X L, Zhang M L, et al. Dynamic development characteristics of two zones of overburden strata under conditions of compound roof, highly gassy and thick coal seam in full-mechanized top coal caving faces[J]. Chinese Journal of Rock Mechanics and Engineering, 2012, 31(S1):3444-3451.
- [9]Baecher G B. Statistical analysis of rock mass fracturing[J]. Journal of the International Association for Mathematical Geology, 1983, 15(2):329-348.
- [10]Warburton P M. Stereological interpretation of joint trace data:influence of joint shape and implications for geological surveys[J]. International Journal of Rock Mechanics and Mining Sciences and Geomechanics Abstracts, 1980, 17(6):305-316.
- [11]Dershowitz W S, Einstein H H. Characterizing rock joint geometry with joint system models[J]. Rock Mechanics and Rock Engineering, 1988, 21(1):21-51.
- [12]Zhang L, Einstein H H, Dershowitz W S. Stereological relationship between trace length and size distribution of elliptical discontinuities[J]. Géotechnique, 2002, 52(6):419-433.
- [13]Jin W C, Gao M Z, Zhang R, et al. Analytical expressions for the size distribution function of elliptical joints[J]. International Journal of Rock Mechanics and Mining Sciences, 2014, 70:201-211.
- [14]Zheng J, Guo J C, Wang J C, et al. A universal elliptical disc(UED)model to represent natural rock fractures[J]. International Journal of Mining Science and Technology, 2022, 32(2):261-270.
- [15]郭吉超.岩体结构面通用椭圆盘模型构建、参数推断及渗流中应用[D].杭州:浙江大学,2023.Guo Jichao. Construction and parameter inference of the universal elliptical disc model for rock mass fractures and its application to seepage[D]. Hangzhou:Zhejiang University, 2023.
- [16]谢晶,高明忠,张茹,等.采动裂隙网络重构分形特征参数敏感性分析[J].中国矿业大学学报,2016, 45(4):677-683.Xie Jing, Gao Mingzhong, Zhang Ru, et al. The parameter sensitivity analysis of mining-induced fracture network reconstructed on the fractal characteristics[J]. Journal of China University of Mining&Technology, 2016, 45(4):677-683.
- [17]欧阳苏.节理岩质边坡结构面参数概率分布更新及可靠性分析[D].南昌:南昌大学,2022.Ouyang Su. Updating of probability distributions of structural plane parameters and reliability analysis of jointed rock slopes[D]. Nanchang:Nanchang University, 2022.
- [18]Barthelémy J F, Guiton M L E, Daniel J M. Estimates of fracture density and uncertainties from well data[J]. International Journal of Rock Mechanics and Mining Sciences, 2009, 46:590-603.
- [19]Li X J, Zuo Y L, Zhuang X Y, et al. Estimation of fracture trace length distributions using probability weighted moments and L-moments[J]. Engineering Geology, 2014, 168:69-85.
- [20]Gao M, Jin W C, Zhang J X, et al. Fracture size estimation using data from multiple boreholes[J]. International Journal of Rock Mechanics and Mining Sciences, 2016, 86:29-41.
- [21]Ye C, Zhang D M, Zhou X, et al. Reconstruction and sampling analysis of parent fracture group in underground mining[J]. Rock Mechanics and Rock Engineering, 2021, 54(12):6155-6172.
- [22]Guo J C, Zheng J, Feng J W, et al. Inference of the preferred direction of fractures in the universal elliptical disc model based on multiple borehole information[J]. International Journal of Rock Mechanics and Mining Sciences, 2025, 193:106171.
- [23]张晶.基于等效管网法的复杂三维裂隙网络渗流特性预测及工程应用[D].徐州:中国矿业大学,2022.Zhang Jing. Prediction of seepage characteristics of complex three-dimensional fracture network based on equivalent pipe network method and its engineering application[D]. Xuzhou:China University of Mining and Technology, 2022.
- [24]武娜,梁正召,宋文成,等.等效岩体三维随机节理网络模型构建及其在两河口水电站中的应用[J].工程科学学报,2022, 44(7):1282-1290.Wu Na, Liang Zhengzhao, Song Wencheng, et al.Construction of a 3D equivalent rock random fracture network model and its application in the Lianghekou Hydropower Station[J]. Chinese Journal of Engineering, 2022, 44(7):1282-1290.
- [25]魏明尧,皇甫昊棋,陆春钦,等.煤岩体基质和裂隙渗透率的试验测算方法[J].中国矿业大学学报,2025, 54(2):413-422.Wei Mingyao, Huangfu Haoqi, Lu Chunqin, et al.Experimental measurement method of matrix and fracture permeability of coal and rock mass[J]. Journal of China University of Mining&Technology,2025, 54(2):413-422.
- [26]Mauldon M, Mauldon J G. Fracture sampling on a cylinder:From scanlines to boreholes and tunnels[J]. Rock Mechanics and Rock Engineering, 1997,30(3):129-144.
- [27]Zheng J, Deng J H, Yang X J, et al. An improved Monte Carlo simulation method for discontinuity orientations based on Fisher distribution and its program implementation[J]. Computers and Geotechnics,2014, 61:266-276.
- [28]Priest S D. Discontinuity analysis for rock engineering[M]. New York:Chapman&Hall, 1993.
- [29]Bonnet E, Bour O, Odling N E, et al. Scaling of fracture systems in geological media[J]. Reviews of Geophysics, 2001, 39(3):347-383.
- [30]Xu W T, Zhang Y S, Li X Z, et al. Extraction and statistics of discontinuity orientation and trace length from typical fractured rock mass:A case study of the Xinchang underground research laboratory site,China[J]. Engineering Geology, 2020, 269:105553.
- [31]王明常,徐则双,王凤艳,等.基于摄影测量获取岩体结构面参数的概率分布拟合检验[J].吉林大学学报(地球科学版),2018, 48(6):1898-1906.Wang Mingchang, Xu Zeshuang, Wang Fengyan,et al. Fitting test on probability distribution of discontinuity parameters in rock mass based on photogrammetry[J]. Journal of Jilin University(Earth Science Edition), 2018, 48(6):1898-1906.
- [32]霍俊杰,Reidar Lovlie,董秀军. 3D激光扫描工艺与锦屏Ⅰ级水电工程右岸建基面绿片岩实测迹长分布研究[J].工程地质学报,2010,18(5):790-795.Huo Junjie, Reidar Lovlie, Dong Xiujun, et al. 3D laser scanning technique and study on trace length distribution of green schist for the right abutment of Jinping I Hydropower Station engineering[J]. Journal of Engineering Geology, 2010, 18(5):790-795.
- [33]韩帅,李明超,王刚.基于控制圆法和迭代反演的岩体多边形裂隙网络模拟方法[J].岩石力学与工程学报,2019, 38(8):1635-1646.Han Shuai, Li Mingchao, Wang Gang. A polygonal DFN modeling approach based on the circlecontrolled method and the iterative inversion algorithm[J]. Chinese Journal of Rock Mechanics and Engineering, 2019, 38(8):1635-1646.
- [34]Kim J, Choi J, Mehrishal S, et al. The goodness-offit of models for fracture trace length distribution:Does the power law provide a good fit?[J]. Journal of Structural Geology, 2024, 189:105270.
- [35]孔祥国,张辉,李树刚,等.基于裂隙场和渗流场融合判识的覆岩分区演化特征及采厚效应[J].中国矿业大学学报,2026,55(1):164-179.Kong Xiangguo, Zhang Hui, Li Shugang, et al.Zonal evolution characteristics of overlying strata and mining thickness effect based on integrated identification of fracture field and seepage field[J]. Journal of China University of Mining&Technology, 2026,55(1):164-179.